Post Reply

Warning - While you were reading a new reply has been posted. You may wish to review your post.

Note: This post will not be displayed until it has been approved by a moderator.

Message Icon:

(Clear Attachment)
(more attachments)
Allowed file types: gif, jpg, pdf, png
Restrictions: 8 per post, maximum total size 800KB, maximum individual size 100KB
Note that any attached files will not be displayed until approved by a moderator.
Spammers have become a daily problem that's why we have to revert to such measures, Please enter "OUR" post code (without the space), in the box below, Our Postcode can be found in our Logo at the top of this page:

Shortcuts: Alt+s to submit/post; Alt+p to preview

Topic Summary

Posted by: HFloyd1987
« on: 13 April 2021, 11:04:15 »

On the supplied deans marine rudder, do you guys sand it down so it’s smooth? Just where the rods connects down the middle sticks out in the middle, thank!

Posted by: HFloyd1987
« on: 02 April 2021, 21:00:08 »

Thanks Colin, that’s mega helpful.
Posted by: colin
« on: 02 April 2021, 20:54:47 »

If you have a look at my Enchantress build, you will see the same stantions..
Mounted, painted in the sugested method... 
I used 0.2mm nickel silver rod, as it's closer to the scale required..
Posted by: HFloyd1987
« on: 02 April 2021, 18:18:14 »

Great thanks for all the advice!
Posted by: Pegasus
« on: 02 April 2021, 14:55:31 »

 Once in place if you are painting them in situ this will hold them in place. You only need to glue sparingly
Posted by: HFloyd1987
« on: 02 April 2021, 14:04:06 »

Great thanks, Dividers is a top tip and thanks I think I’ve got a good idea how I’ll do it now.  With the wire do you just drop some glue on each section once you’ve threaded it through?
Posted by: Pegasus
« on: 02 April 2021, 11:29:51 »

Its hard to tell it will either be for 0.5mm to 1mm wire you will require. I have used individual stanchions many times. This is normally the last part of the build. I measure using dividers along the deck and the drill locating holes for the stanchions. Paint the bottom of the stanchions that helps when you finally fit them and insert the wire. Once the stanchions and rails are in place then they can be carefully painted
Posted by: HFloyd1987
« on: 01 April 2021, 23:38:22 »

Here's the picture of the stanchions for HMS Amazon.
Posted by: HFloyd1987
« on: 01 April 2021, 10:47:24 »

I’ll ping a picture tonight of the stanchions from the Amazon, I’m playing about with running gear and drilling holes.
Posted by: Pegasus
« on: 01 April 2021, 10:38:01 »

scuppers inboard along the side of the deck as in your picture the horizontal ones are unique to the Solebay

stanchions/ handrails  The ones that were used in the Solebay were spring brass in 8 inch lengths what are the stanchions on the Amazon
Posted by: HFloyd1987
« on: 31 March 2021, 20:12:27 »

Hi Pegagus,

Thanks for the reply.

Rigging - got it and found the material in the kit pretty much after i posted this. So i guess they are tied on?

Stanchions - do you use the brass wire to thread into between?

Scuppers - i'm really sorry, on your picture do you mean inboard along the side of the deck? Or the Horizontal pieces running from port to starboard? i've attached the Dean's build photo (Copyright Deansmarine). Is it those thin pieces along the side of the deck?

Thanks so much!

Posted by: Pegasus
« on: 31 March 2021, 19:33:07 »

•   Scuppers, easily done by fitting fine strips inboard along the deck see picture these should be on your plan
Posted by: Pegasus
« on: 31 March 2021, 19:32:47 »

Stanchion/Handrails: these come in lengths and should be the last to be fitted by drilling location holes
•   Rigging: using a suitable thread see picture
•   Scuppers, easily done by fitting fine strips inboard along the deck see picture
Posted by: HFloyd1987
« on: 31 March 2021, 16:45:08 »

Hi all,
A relative newcomer to the world of RC ship modelling. Have done more basic builds, but have kicked off my Deans Marine journey with HMS Amazon.
I’ll share some photos soon, I’ve pretty much prepared the hull and installing the running gear now. I am however I am a planner and like to have an idea of the stage of a build quite early on.
Can anyone guide me to a post/topic on these parts or help with a few queries.
•   Stanchion/Handrails: I think the kit now comes with some very good brass etchings. The Instructions I think may refer to older pieces in the kit. They talk about soldering individual Stanchion. But are they made in one piece now? Or do you cut them out, glue them down and thread coper wire through them for safety rails?
•   Rigging: How do people usually do the rigging, due you glue wire in place on the Masts/deck or tie them off somewhere? Not really mentioned from what I can see.
•   Scuppers, sorry if this sounds silly, I did not realise what these were on a ship. I can see it’s a piece of mini strip along the lower deck, do we also place them on the Fo’castle?
Thanks for any help or tips,